Southern Indiana & Louisville · Local home servicesFor local businesses

Furnace Won't Turn On? 8 Things to Check Before You Call

The first cold night is when furnaces quit. Most no-heat calls start with something simple. Here's what to check in about 15 minutes, and when to stop and call.

Furnace Won't Turn On? 8 Things to Check Before You Call
The short version: If your furnace won't turn on, start with the thermostat, the power switch, the breaker and the filter. Those four cause a lot of no-heat nights, and you can check all of them in about 15 minutes without tools. If none of them fixes it, or you smell gas, stop and call for help.

The first cold night of the year is when furnaces show their problems. The system has sat all summer, and now it has to run for hours. Here's the order we'd check things in, and the point where it stops being a DIY job.

Safety first. If you smell rotten eggs (gas) or your carbon monoxide alarm is going off, skip this list. Get everyone outside, then call 911 and your gas company from outside. On the Kentucky side, LG&E's gas leak line is 502-589-1444 or 800-331-7370 (LG&E gas safety). In Southern Indiana, use the emergency number on your CenterPoint Energy bill (CenterPoint: report a gas leak).

1. The thermostat

  • Set it to Heat, not Cool or Off.
  • Turn the temperature a few degrees above what the room is now.
  • If the screen is blank or dim, put in fresh batteries. Many thermostats run on AA or AAA batteries even when they're wired in.
  • If you have a smart thermostat, check that it's online and that no schedule or "eco" setting is holding the temperature down. Our smart thermostat guide covers the common settings.

2. The furnace power switch

Most furnaces have a switch on the wall or the side of the unit that looks like a regular light switch. It's easy to flip off by accident when you're storing things in the basement or utility closet. Make sure it's on.

3. The breaker

Check your electrical panel for a tripped breaker labeled furnace, HVAC or air handler. A tripped breaker sits in the middle or off position. Flip it fully off, then back on. If it trips again, leave it off and call a pro. A breaker that keeps tripping is telling you something is wrong.

4. The filter

A clogged filter chokes the airflow. Many furnaces have a safety switch that shuts the burner off when the unit runs too hot, so a dirty filter can look like a dead furnace. Pull the filter and hold it up to a light. If you can't see light through it, replace it. Here's how to change an HVAC filter.

5. The front panel

Furnaces have a safety switch behind the front door or panel. If the panel isn't seated all the way, the furnace won't run. Push it closed firmly until it sits flat.

6. The gas supply

Look at the gas valve on the line going into the furnace. The handle should run in the same direction as the pipe. If your stove or water heater also runs on gas and they aren't working either, the problem may be the gas service, not the furnace. Call your gas company.

7. The vent pipes outside

High-efficiency furnaces often vent through two white plastic pipes on the side of the house. Leaves, a bird nest or drifted snow can block them, and the furnace will shut itself off. Clear anything around the pipe openings by hand. Don't push anything into the pipes.

These furnaces also drain water through a small tube or a condensate pump. If the pump's tank is full or the drain line is clogged, the furnace can stop. Water pooling around the furnace is a sign of this one.

8. The blinking light

Most modern furnaces have a small light you can see through a window in the lower panel. It blinks in a pattern when something is wrong. Count the blinks and match them to the chart, usually printed on the inside of the furnace door. Write the code down. Even if you can't fix it, the HVAC company will want it.

When to stop and call an HVAC pro

Call a heating contractor if:

  • You smell gas or your CO alarm sounds (leave first, call from outside)
  • The breaker trips again after you reset it
  • The furnace clicks or tries to light but never fires
  • The burner lights, then shuts off after a few minutes, over and over
  • You smell burning that lasts past the first few minutes of the season's first run, or it smells electrical
  • You hear banging, grinding or squealing
  • The blinking code points to a part, not a setting

A dusty smell the first time the heat runs each fall is common. A smell that lingers is not.

What to tell the HVAC company when you call

You'll get a faster, clearer answer if you have this ready:

  • The furnace brand and model (on a sticker inside the door)
  • About how old it is
  • The blinking light code, if any
  • What you already checked from this list
  • Whether you have a gas, electric or heat pump system

If your furnace is near the end of its life and you're being quoted a replacement, our heat pump estimate questions help you compare quotes.

Keep it from happening next year

Find furnace repair near you

Find heating and cooling contractors serving Louisville and Southern Indiana in our HVAC directory. Each listing shows the areas the company serves and how to reach them directly.

Frequently asked questions

Why is my furnace blowing cold air?

Check that the thermostat fan is set to Auto, not On. On "On", the blower runs even when the burner is off. If it's on Auto and still blowing cold, check the filter and the outside vent pipes, then call a pro.

Can a dirty filter stop a furnace from working?

Yes. A clogged filter cuts airflow, the furnace overheats, and a safety switch shuts the burner off. Replacing the filter is the cheapest fix on this list.

Is it safe to reset my furnace?

Turning the power switch off for 30 seconds and back on is a common reset. If the furnace locks out again, stop resetting it and call a technician. Repeated resets can hide a real problem.

What does a blinking light on my furnace mean?

It's an error code. Count the blinks and match them to the chart on the inside of the furnace door. Give that code to the HVAC company when you call.

What should I do if my CO alarm goes off?

Get everyone outside to fresh air and call 911. Don't go back in until responders say it's safe.

Local note: Requirements, availability, and pricing can change by project and jurisdiction. Verify current details with the appropriate authority and the business you hire.

Editorial standards and source information · Report a correction

Explore HVAC businesses

Compare listed services, then call a company directly to discuss your project, availability, and pricing.

Browse local hvac companies

  1. Say the job and the address and when you'd like it done.
  2. Call two or three and notice who answers your questions.
  3. Get the estimate in writing before anyone starts.

Compare your shortlist

Compare the services listed in each company’s sources. Confirm current scope directly with the business.